 |
 |
|
 |
© 1999-2004
Association of Lifecasters International
All rights reserved.
|
|
|
|
|
|
FORUMS
|
|
|
|
|
  |
| Author |
Message |
Ed McCormick
Joined:
:
21-Mar-2004
|
Started On : 27-May-2005 at 11:30:44 AM, #Views : 11966
Topic Subject : RE: Casting Hockey player |
|
Casting fabric is not as difficult as this thread makes out . . . though it
requires a bit of practice. I am attaching a picture of a Roy Butler piece
which is almost 90% fabric based. Roy has stopped contributing to the forum
because of past rude responses. But he does read it.
Roy has shown me his marvelous technique which I have used on a few pieces
with exquisite results.
Perhaps members can convince him to rejoin the forum as he a font of
technical expertise. Send your fan mail to: rbicom@earthlink.net
Warmest regards
Ed
A R T M O L D S
"The Art of Imitating Life"
Alginates / Silicones / Resins / Urethanes / Latex / Waxes
Life Casting Supplies / Kits / Videos / Books / Workshops
www.artmolds.com
Toll Free US 1-866-ARTMOLDS (278-6653)
International 1-908-273-5401
Fax 1-908-273-9256
18 Bank Street / Summit NJ 07901 USA
CHARTER MEMBER OF ALI SINCE 2000
Association of Lifecasters International
-----Original Message-----
From: aliforum@lifecasting.org [mailto:aliforum@lifecasting.org]
Sent: Friday, May 27, 2005 10:00 AM
To: info@artmolds.com
Subject: RE: Casting Hockey player( Message No. 476)
-----------------Amazon.com ALI Sponsor -------->
Three life casting DVDs available. Hands & Feet
Face Casting and Female Torso Casting. Available
through http://www.Amazon.com
-------------------------------------------------------->
Hello Ed McCormick
Post Date : Friday 27th of May 2005 11:00:01 AM
Posted by : "John Collins" johncollins@concreterepair.com
RE: Casting Hockey player:--
Maybe the fabric can be treated first with a release agent or treat the
fabric with a clear acrylic?
John
Laguna Beach, Ca
-----Original Message-----
From: aliforum@lifecasting.org [mailto:aliforum@lifecasting.org]
Sent: Friday, May 27, 2005 5:31 AM
To: johncollins@concreterepair.com
Subject: Re: Casting Hockey player( Message No. 475)
-----------------Amazon.com ALI Sponsor -------->
Three life casting DVDs available. Hands & Feet
Face Casting and Female Torso Casting. Available
through http://www.Amazon.com
-------------------------------------------------------->
Hello John Collins
Post Date : Friday 27th of May 2005 09:30:01 AM
Posted by : "CJ Munn" cj@rockabelly.co.uk
Re: Casting Hockey player:--
I don't know if you could get a sample of the fabric of his shirt or
similar, but I have managed to cast some fabrics without any release
agent. It works better on fabrics with a very tight weave, particularly
modern man-made slightly shiny fabrics. If you can get a duplicate you
could run some tests. You have to use a very strong, thick mix of
alginate and pull it off very slowly...in some ways it's easier if your
model can slip out of the shirt when you come to demould him, leaving
the loose shirt still stuck in the mould and then you can take all the
time you want to carefully peel the fabric out.
other than that, the only thing i can think of is to sculpt on a fake
shirt after you've done the cast.
cj x
On 25 May 2005, at 05:57, aliforum@lifecasting.org wrote:
> -----------------Amazon.com ALI Sponsor -------->
>
> Three life casting DVDs available. Hands & Feet
> Face Casting and Female Torso Casting. Available
> through http://www.Amazon.com
> -------------------------------------------------------->
>
> Hello CJ Munn
>
>
> Post Date : Wednesday 25th of May 2005 12:57:06 AM
> Posted by : "Jimmy F" wave@kooee.com.au
>
> Casting Hockey player:--
> Hi guys and gals, I havent posted on here in quite sometime, so
> hopfully some of you can give your opinion to my delmema....
> I have been commisioned to create a sculpture or a Hockey player and a
> figureskater. The fingure skater will not be too hard as she can be in
> a slim tight suite of some kind, but my problem is with the hockey
> player... Because the jersey is a loose fitting type, im not sure how
> i will be able to make the sculpture look proper without it looking
> like a wet soggy shirt. Secondly the skate blade will be so small and
> thin, what would be the best way to support this sculpture for both
> the figure skater and the hockey player.
>
> Any suggestions???
>
> Kind Regards
> Jimmy
>
> ALI is an international organization whose members are engaged in the
> art and creative industries. Its purpose is to promote the art of life
> casting, create public awareness of this unique art form, provide its
> members with forums to exchange information, resources to enhance
> their effectiveness and advance opportunities for their artistic
> success.
ALI is an international organization whose members are engaged in the art
and creative industries. Its purpose is to promote the art of life casting
create public awareness of this unique art form, provide its members with
forums to exchange information, resources to enhance their effectiveness and
advance opportunities for their artistic success.
ALI is an international organization whose members are engaged in the art
and creative industries. Its purpose is to promote the art of life casting
create public awareness of this unique art form, provide its members with
forums to exchange information, resources to enhance their effectiveness and
advance opportunities for their artistic success.
|
| View File |
|
|
| |
|
|
|
|
)
)
)
)
)
)
)
)
)
)
